Changes between Version 55 and Version 56 of Tutorials/Wireless/mmwaveSB1

Timestamp:

Sep 21, 2021, 4:25:26 PM (3 years ago)

Author:

prasanthi

Comment:

—

Tutorials/Wireless/mmwaveSB1

@@ -25 +25 @@
 
 === Resources required ===
-2 servers srv1-in1, srv1-in2, 2 USRP N310s sdr1-in1, sdr1-in2 and both the Sivers mmWave platforms rfdev3-in1, rfdev3-in2 on COSMOS SB1.
+2 servers srv1-in1, srv1-in2, 2 USRP X310s sdr4-in1, sdr4-in2 and both the Sivers mmWave platforms rfdev3-in1, rfdev3-in2 on COSMOS SB1.
 === Tutorial Setup ===
 
@@ -34 +34 @@
  1. Make sure all the nodes and devices used in the experiment are turned off:
 {{{#!shell
-omf tell -a offh -t srv1-in1,srv1-in2,sdr1-in1,sdr1-in2,rfdev3-in1,rfdev3-in2  
+omf tell -a offh -t srv1-in1,srv1-in2,sdr4-in1,sdr4-in2,rfdev3-in1,rfdev3-in2  
 }}}
  1. The image sivers_sb1_cosmos.ndz is [baseline_uhd.ndz] with Sivers control software installed.   
@@ -43 +43 @@
  1. Turn all the required resources on and check the status
 {{{#!shell
-omf tell -a on -t srv1-in1,srv1-in2,sdr1-in1,sdr1-in2,rfdev3-in1,rfdev3-in2
+omf tell -a on -t srv1-in1,srv1-in2,sdr4-in1,sdr4-in2,rfdev3-in1,rfdev3-in2
 }}}
 {{{#!shell
@@ -54 +54 @@
 ==== Find and prepare USRPs ====
 
-* The IP addresses for Ethernet Port 1(10G) on the X310s rfdev3-1 and rfdev3-2 were hard-coded to 10.115.6.1 and 10.115.6.2 respectively. To access them from srv3-lg1 or srv4-lg1, configure the network interface enp1s0 of srv3-lg1 to 10.115.1.3 and srv4-lg1 to 10.115.1.4, as follows
+* The IP addresses for Ethernet Ports(10G) on the X310s sdr4-in1 and sdr4-in2 were hard-coded to 10.114.14.1,10.115.14.1 and 10.114.14.2,10,115,14,2 respectively. To access them from srv1-in1 or srv1-in2, configure the network interfaces as follows
+|| Server || enp1s0 || enp3s0 ||
+|| srv1-in1 || 10.114.1.3 || 10.115.1.3 ||
+|| srv1-in2 || 10.114.1.4 || 10.115.1.4 ||
 {{{#!shell-session
-root@srv3-lg1:~# ip link set enp1s0 mtu 9000 up
-root@srv3-lg1:~# ip addr add 10.115.1.3/16 dev enp1s0
-root@srv3-lg1:~# ip addr show dev enp1s0
+root@srv1-in1:~# ip link set enp1s0 mtu 9000 up
+root@srv1-in1:~# ip addr add 10.114.1.3/16 dev enp1s0
+root@srv1-in1:~# ip addr show dev enp1s0
 4: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc mq state UP group default qlen 1000
-    link/ether f4:52:14:83:b9:30 brd ff:ff:ff:ff:ff:ff
-    inet 10.115.1.3/16 brd 10.115.255.255 scope global enp1s0
+    link/ether f4:52:14:83:99:40 brd ff:ff:ff:ff:ff:ff
+    inet 10.114.1.3/16 scope global enp1s0
        valid_lft forever preferred_lft forever
-    inet6 fe80::f652:14ff:fe83:b930/64 scope link
+    inet6 fe80::f652:14ff:fe83:9940/64 scope link
        valid_lft forever preferred_lft forever
-
 }}}
 
 * Run uhd_find_devices to check if the X310s can be reached
 {{{#!shell-session
-root@srv3-lg1:~# uhd_find_devices --args="addr=10.115.6.1"
+root@srv1-in1:~# uhd_find_devices --args="addr=10.114.14.1"
 [INFO] [UHD] linux; GNU C++ version 7.4.0; Boost_106501; UHD_3.14.1.1-release
 --------------------------------------------------
@@ -77 +79 @@
 Device Address:
     serial: 31B8F3F
-    addr: 10.115.6.1
+    addr: 10.114.14.1
     fpga: XG
-    name: rfdev3-1
+    name: sdr4-in1
     product: X310
     type: x300