| | 1 | [[Include(WikiToC)]] |
| | 2 | |
| | 3 | == FR3 SDRs |
| | 4 | |
| | 5 | This setup is designed for advanced wireless research and prototyping in FR3 frequency bands, supporting next-generation 5G/6G air interface and 2×2 MIMO experimentation. |
| | 6 | |
| | 7 | [[Image(FR3-BD.png, width=800px)]] |
| | 8 | |
| | 9 | As can be seen in the block diagram, the COSMOS FR3 experimental setup consists of two units each using a combination of USRP-2974 (Krypton) SDRs and Pi-Radio FR3 SDR front-end hardware. The Pi-Radio FR3 SDR units can be configured to operate across the entire 6 GHz to 24 GHz range, supporting experimentation in the full FR3 band. |
| | 10 | |
| | 11 | === [https://www.pi-rad.io/ Pi-Radio] FR3 SDR |
| | 12 | The [https://www.pi-rad.io/ Pi-Radio] FR3 front-end includes a wideband RF transceiver board capable of two-stage up- and down-conversion to meet stringent out-of-band (OOB) and adjacent channel rejection (ACLR) requirements, as well as strict spectral masks. Each FR3 front-end supports 2×2 MIMO via connections to a pair of Vivaldi antennas for transmit (Tx1, Tx2) and receive (Rx1, Rx2). The digital baseband board allows the FR3 front-end to be connected via SMA cables to any sub-6 GHz SDR (e.g., USRP, Xilinx RFSoC, Pluto), providing maximum flexibility for rapid prototyping and experimentation in upper mid-band/FR3 spectrum. The platform supports advanced research use cases such as end-to-end 5G/6G OpenAirInterface (OAI) links, O-RAN compliant radio units, and channel sounding for propagation and spatial studies. |
| | 13 | |
| | 14 | === [https://www.ettus.com/all-products/usrp-2974/ USRP-2974 (Krypton)]: |
| | 15 | The [https://www.ettus.com/all-products/usrp-2974/ USRP-2974] is an integrated software-defined radio platform with a quad-core Intel i7 processor, 8 GB RAM, 256 GB SSD, and embedded X310 radio supporting wideband operation. It supports high-throughput data movement either via the internal PCI Express bus or external 10 GbE, providing a flexible and powerful baseband processing environment for advanced wireless prototyping. |
| | 16 | |
| | 17 | The USRP-2974 connects to the Pi-Radio FR3 SDR front-end module through a set of 20 dB attenuators, which perform up/down-conversion between sub-6 GHz and FR3 frequencies. The units are interconnected via dual sub-6 GHz RF paths with variable attenuation, enabling flexible RF experimentation and emulation of over-the-air links. |
| | 18 | |
| | 19 | The FR3 RF front-ends are configured over Ethernet at addresses rfdev-sdr1-piradio.sb1.cosmos-lab.org and rfdev-sdr2-piradio.sb1.cosmos-lab.org, while the two baseband USRPs can be accessed via sdr1-piradio.sb1.cosmos-lab.org and sdr2-piradio.sb1.cosmos-lab.org. |
| | 20 | |
| | 21 | === Tutorials |
| | 22 | |
| | 23 | * [wiki:./Wireless/FR3Sine Basic Narrowband Sinewave (UHD-based) Link] |
| | 24 | * [wiki:./Wireless/FR3Analog Analog FM Link with GNURadio] |
| | 25 | |
| | 26 | |
