mmWave Channel Sounding on SandBox1 (IN PROGRESS)

Description

Prerequisites

In order to access the test bed, create a reservation and have it approved by the reservation service. Access to the resources is granted after the reservation is confirmed. Please follow the process shown on the COSMOS work flow page to get started.

Resources required

4 servers srv1-lg1 to srv4-lg1, 2 USRP X310s rfdev3-1, rfdev3-2 and both the Sivers platforms rfdev3-5, rfdev3-6 on COSMOS SB1.

Execution

Prepare host nodes

• The image rfnoc_wigig.ndz has aforementioned RFNoC 802.11ad preamble processing blocks installed. Load rfnoc_wigig.ndz on srv1,srv2

  prasanthi@console:~$ omf load -i rfnoc_wigig.ndz -t srv1-lg1,srv2-lg1
  

• The image sivers_sb1_cosmos.ndz has UHD and Sivers control software installed. Load sivers_sb1_cosmos.ndz on srv3,srv4

  prasanthi@console:~$ omf load -i sivers_sb1_cosmos.ndz -t srv3-lg1,srv4-lg1
  

• Turn the servers on

  prasanthi@console:~$ omf tell -a on -t srv1-lg1,srv2-lg1,srv3-lg1,srv4-lg1
  

• Check the status

  prasanthi@console:~$ omf stat -t system:topo:allres
  

   -----------------------------------------------
   Node: rfdev1-1.sb1.cosmos-lab.org       State: POWERON
   Node: rfdev1-2.sb1.cosmos-lab.org       State: POWERON
   Node: rfdev2-1.sb1.cosmos-lab.org       State: POWERON
   Node: rfdev2-2.sb1.cosmos-lab.org       State: POWERON
   Node: rfdev3-1.sb1.cosmos-lab.org       State: POWERON
   Node: rfdev3-2.sb1.cosmos-lab.org       State: POWERON
   Node: rfdev3-3.sb1.cosmos-lab.org       State: POWERON
   Node: rfdev3-4.sb1.cosmos-lab.org       State: POWERON
   Node: rfdev3-5.sb1.cosmos-lab.org       State: POWERON
   Node: rfdev3-6.sb1.cosmos-lab.org       State: POWERON
   Node: sdr1-md1.sb1.cosmos-lab.org       State: POWERON
   Node: sdr1-s1-lg1.sb1.cosmos-lab.org            State: POWERON
   Node: sdr2-md1.sb1.cosmos-lab.org       State: POWERON
   Node: sdr2-s1-lg1.sb1.cosmos-lab.org            State: POWERON
   Node: srv1-lg1.sb1.cosmos-lab.org       State: POWERON
   Node: srv2-lg1.sb1.cosmos-lab.org       State: POWERON
   Node: srv3-lg1.sb1.cosmos-lab.org       State: POWERON
   Node: srv4-lg1.sb1.cosmos-lab.org       State: POWERON
  -----------------------------------------------  
  

• ssh to the nodes, use option -Y if using GUI.

• The IP addresses for Ethernet Port 1(10G) on the X310s sdr2-md2 and sdr2-md3 were hard-coded to 10.115.2.2 and 10.115.2.3 respectively. To access them from srv1-lg1 or srv2-lg2, configure the network interface eno2 as follows

  root@srv2-lg1:~# ifconfig eno2 10.115.1.1 netmask 255.255.0.0 mtu 9000 up
  root@srv2-lg1:~# ifconfig eno2
  eno2: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 9000
          inet 10.115.1.1  netmask 255.255.0.0  broadcast 10.115.255.255
          inet6 fe80::9a03:9bff:fe61:b0b1  prefixlen 64  scopeid 0x20<link>
          ether 98:03:9b:61:b0:b1  txqueuelen 1000  (Ethernet)
          RX packets 4661357820  bytes 37005247545892 (37.0 TB)
          RX errors 0  dropped 692293  overruns 0  frame 0
          TX packets 59454137  bytes 3576874343 (3.5 GB)
          TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
  

• Run uhd_find_devices to check if the X310s can be reached

  root@srv2-lg1:~# uhd_find_devices --args="addr=10.115.2.3"
  [INFO] [UHD] linux; GNU C++ version 7.4.0; Boost_106501; UHD_3.14.1.1-release
  --------------------------------------------------
  -- UHD Device 0
  --------------------------------------------------
  Device Address:
      serial: 31B6FFA
      addr: 10.115.2.3
      fpga: HG
      name: sdr2-md3
      product: X310
      type: x300
  

Prepare USRPs

• Check which RFNoC blocks the are loaded on the X310s, by running uhd_usrp_probe

  root@srv1-lg1:~# uhd_usrp_probe --args="addr=10.115.2.2"
  

• Following is the list of RFNoC blocks required for the experiment

  |   |   |       RFNoC blocks on this device:
  |   |   |
  |   |   |   * DmaFIFO_0
  |   |   |   * Radio_0
  |   |   |   * Radio_1
  |   |   |   * PacketDetector_0
  |   |   |   * CFOC_0
  |   |   |   * DDC_0
  |   |   |   * DUC_0
  |   |   |   * FIR_0
  |   |   |   * SymbolTiming_0
  |   |   |   * BoundaryDetector_0
  |   |   |   * CIR_0
  |   |   |   * FIFO_0
  |   |   |   * FIFO_1
  
  

• If the required RFNoC blocks are not found, load X310 with MISO_IMAGE_x300.bit

  root@srv1-lg1:~# uhd_image_loader --args="addr=10.115.2.2,type=x300" --fpga-path="ORCA_MISO_PROJECT/FPGA_IMAGES/MISO_IMAGE_x300.bit"
  

• Power cycle X310 to use the new image, and run uhd_usrp_probe to check RFNoC blocks.

  root@console:~# omf tell -a offh -t rfdev3-1
  

  root@console:~# omf tell -a on -t rfdev3-1
  

Prepare Sivers 60GHz front-ends

Run the experiment

• Start transmit application TX_TEST.grc on transmit node(srv1-lg1).

  root@srv1-lg1:~# gnuradio-companion TX_TEST.grc
  

• Start receive application RX_OTA_TEST.grc on receive node(srv2-lg1).

  root@srv2-lg1:~# gnuradio-companion RX_OTA_TEST.grc