| Version 2 (modified by , 2 years ago) ( diff ) |
|---|
Site Navigation
Amarisoft 5G Network with COTS UEs ¶
Description ¶
This tutorial contains instructions for setting up amarisoft 5G NR network using COTS user equipment. Amarisoft provides software based gNB, 5GCore (eNB,EPC), and UE simulator that run on commodity off-the-shelf devices. A typical software-based cellular basestation/UE consists of a host PC and an SDR, where host PC is used for processing the baseband signals sent to and received from the SDR. Amarisoft supports various SDRs including USRPs such as N310, X310. In this tutorial, we run 5GCore, gNB(SA) on a host server+USRP N310 in COSMOS SB1. The UEs used in this experiment are 1)SIM8200EA USB modem 2)OnePlus8T KB2005 phone
Prerequisites ¶
In order to access the test bed, create a reservation and have it approved by the reservation service. Access to the resources is granted after the reservation is confirmed. Please follow the process shown on the COSMOS getting started page to get started.
Resources required ¶
2 servers, 2 USRP N310s in COSMOS SB1 domain
Tutorial Setup ¶
Follow the steps below to gain access to the sandbox 1 console and set up nodes with appropriate images.
- If you don't have one already, sign up for a COSMOS account
- Create a resource reservation on sandbox 1
- Login into sandbox 1 console (console.sb1.cosmos-lab.org) with two SSH sessions.
- Make sure all the resources in the domain are turned off:
For this tutorial we will be using the SB1 servers, srv1-lg1, srv2-lg1 and USRP N310s, sdr1-md1, sdr1-s1-lg1
omf tell -a offh -t system:topo:allres
- Load amarisoft-tutorial-cosmos.ndz on srv1-lg1,srv2-lg1.
omf load -i amarisoft-tutorial-cosmos.ndz -t srv1-lg1,srv2-lg1
- Turn all the required resources on and check the status
omf tell -a on -t srv1-lg1,srv2-lg1,sdr1-md1,sdr1-s1-lg1
omf stat -t system:topo:allres
- ssh to the nodes, use option -Y for using GUI.
Tutorial Execution ¶
Check the USRPs
- Upon logging into the nodes, run eth_config.sh script on both the nodes. This sets up the 10G data interfaces DATA1, DATA2. After running the script, you should see that the data interfaces have the appropriate IP addresses assigned, as per this table. The nodes should then be able to access the USRP N310s sdr1-s1-lg1 and sdr1-md1 which can be checked by running uhd_find_devices.
root@srv1-lg1:~# ./eth_config.sh root@srv1-lg1:~# ifconfig DATA1 DATA1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 9000 inet 10.38.1.1 netmask 255.255.0.0 broadcast 10.38.255.255 inet6 fe80::1e34:daff:fe42:c3c prefixlen 64 scopeid 0x20<link> ether 1c:34:da:42:0c:3c txqueuelen 1000 (Ethernet) RX packets 61195963 bytes 199994153268 (199.9 GB) RX errors 0 dropped 6680 overruns 0 frame 0 TX packets 58734853 bytes 190912589303 (190.9 GB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 root@srv1-lg1:~# ifconfig DATA2 DATA2: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 9000 inet 10.39.1.1 netmask 255.255.0.0 broadcast 10.39.255.255 inet6 fe80::1e34:daff:fe42:c3d prefixlen 64 scopeid 0x20<link> ether 1c:34:da:42:0c:3d txqueuelen 1000 (Ethernet) RX packets 7378 bytes 651944 (651.9 KB) RX errors 0 dropped 6682 overruns 0 frame 0 TX packets 282 bytes 82239 (82.2 KB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 | root@srv1-lg1:~# uhd_find_devices [INFO] [UHD] linux; GNU C++ version 7.5.0; Boost_106501; UHD_3.15.0.0-release -------------------------------------------------- -- UHD Device 0 -------------------------------------------------- Device Address: serial: 3176DF5 addr: 10.38.2.1 claimed: False mgmt_addr: 10.37.2.1 mgmt_addr: 10.38.2.1 mgmt_addr: 10.39.2.1 product: n310 type: n3xx -------------------------------------------------- -- UHD Device 1 -------------------------------------------------- Device Address: serial: 3196937 addr: 10.38.3.1 claimed: False mgmt_addr: 10.37.3.1 mgmt_addr: 10.38.3.1 mgmt_addr: 10.39.3.1 product: n310 type: n3xx |
Run MME
- We are going to run the MME, gNodeB on srv1-lg1 and the UE simulator on srv2-lg1.
- Run the Amarisoft MME on srv1-lg1. Run lte_init.sh to setup IP forwarding so that the UEs can connect to the Internet, once they establish a connection with the base station.
This network uses PLMN 310014 (USA Test network) as configured in mme.cfg.
root@srv1-lg1:~# cd /opt/amarisoft/ltemme-linux-2021-09-18 root@srv1-lg1:/opt/amarisoft/ltemme-linux-2021-09-18# ./lte_init.sh Select CTRL default interface root@srv1-lg1:/opt/amarisoft/ltemme-linux-2021-09-18# ./ltemme config/mme.cfg Core version 2021-09-18, Copyright (C) 2012-2021 Amarisoft This software is licensed to Rutgers University (The State University of New Jersey). License server: license.orbit-lab.org (0b-b4-46-dc-2f-83-58-cb) Support and software update available until 2022-08-18. (mme)
- Type 'help' at the prompt to explore the available mme commands.
Run eNodeB/gNodeB
- Run Amarisoft 5G NR Stand alone gNodeB as shown below by passing the gNodeB configuration file as an argument. The configuration file defines SDR(USRP N310) address, operating band, bandwidth and other parameters. To run 4G LTE eNodeB, please use enb-n310.cfg
root@srv1-lg1:~# cd /opt/amarisoft/lteenb-linux-2021-09-18 root@srv1-lg1:/opt/amarisoft/lteenb-linux-2021-09-18# ./lteenb config/gnb-sa-n310.cfg Base Station version 2021-09-18, Copyright (C) 2012-2021 Amarisoft This software is licensed to Rutgers University (The State University of New Jersey). License server: license.orbit-lab.org (0b-b4-46-dc-2f-83-58-cb) Support and software update available until 2022-08-18. [INFO] [UHD] linux; GNU C++ version 7.5.0; Boost_106501; UHD_3.15.0.0-release [INFO] [MPMD] Initializing 1 device(s) in parallel with args: mgmt_addr=10.38.2.1,type=n3xx,product=n310,serial=3176DF5,claimed=False,addr=10.38.2.1,master_clock_rate=122.88e6 [INFO] [MPM.PeriphManager] init() called with device args `product=n310,mgmt_addr=10.38.2.1,time_source=internal,clock_source=internal,master_clock_rate=122.88e6'. [INFO] [0/Replay_0] Initializing block control (NOC ID: 0x4E91A00000000004) [INFO] [0/Radio_0] Initializing block control (NOC ID: 0x12AD100000011312) [INFO] [0/Radio_1] Initializing block control (NOC ID: 0x12AD100000011312) [INFO] [0/DDC_0] Initializing block control (NOC ID: 0xDDC0000000000000) [INFO] [0/DDC_1] Initializing block control (NOC ID: 0xDDC0000000000000) [INFO] [0/DUC_0] Initializing block control (NOC ID: 0xD0C0000000000002) [INFO] [0/DUC_1] Initializing block control (NOC ID: 0xD0C0000000000002) [INFO] [0/FIFO_0] Initializing block control (NOC ID: 0xF1F0000000000000) [INFO] [0/FIFO_1] Initializing block control (NOC ID: 0xF1F0000000000000) [INFO] [0/FIFO_2] Initializing block control (NOC ID: 0xF1F0000000000000) [INFO] [0/FIFO_3] Initializing block control (NOC ID: 0xF1F0000000000000) RF0: sample_rate=30.720 MHz dl_freq=3489.420 MHz ul_freq=3489.420 MHz (band n78) dl_ant=2 ul_ant=1 (enb) WARNING: The GPS is not locked. If you need time synchronization, you should restart the program when the GPS is locked. Chan Gain(dB) Freq(MHz) TX1 35.0 3489.420000 TX2 35.0 3489.420000 RX1 40.0 3489.420000 (enb) ng gNB NG connection state: - server=127.0.1.100:38412 state=setup_done PLMN=310014 (enb) cell phy [gnb0012345] PLMN=310014 gNB_ID=0x12345 --------Global-------- ----------DL---------- ----------UL---------- ----SSB--- Cell RAT BAND BW P ARFCN ANT NL SCS QAM ARCFN ANT NL SCS QAM ARFCN SCS 0x001 NR n78 20 0 632628 2 2 30 256 632628 1 1 30 256 632544 30 (enb)
- Type 'help' at the prompt and use commands like 'cell phy' to look at the various parameters of the base station.
Run Amarisoft UE Simulator
- Run the Amarisoft UE simulator on srv2-lg1 by passing the configuration file ue-nr-sa-n310.cfg as an argument. To run UE simulator in 4G LTE mode, please use ue-n310.cfg.
root@srv2-lg1:~# cd /opt/amarisoft/lteue-linux-2021-09-18 root@srv2-lg1:/opt/amarisoft/lteue-linux-2021-09-18# ./lteue config/ue-nr-sa-n310.cfg LTE UE version 2021-09-18, Copyright (C) 2012-2021 Amarisoft This software is licensed to Rutgers University (The State University of New Jersey). License server: license.orbit-lab.org (0b-b4-46-dc-2f-83-58-cb) Support and software update available until 2022-08-18. [INFO] [UHD] linux; GNU C++ version 7.5.0; Boost_106501; UHD_3.15.0.0-release [INFO] [MPMD] Initializing 1 device(s) in parallel with args: mgmt_addr=10.38.3.1,type=n3xx,product=n310,serial=3196937,claimed=False,addr=10.38.3.1,master_clock_rate=122.88e6 [INFO] [MPM.PeriphManager] init() called with device args `clock_source=internal,mgmt_addr=10.38.3.1,time_source=internal,master_clock_rate=122.88e6,product=n310'. [INFO] [0/Replay_0] Initializing block control (NOC ID: 0x4E91A00000000004) [INFO] [0/Radio_0] Initializing block control (NOC ID: 0x12AD100000011312) [INFO] [0/Radio_1] Initializing block control (NOC ID: 0x12AD100000011312) [INFO] [0/DDC_0] Initializing block control (NOC ID: 0xDDC0000000000000) [INFO] [0/DDC_1] Initializing block control (NOC ID: 0xDDC0000000000000) [INFO] [0/DUC_0] Initializing block control (NOC ID: 0xD0C0000000000002) [INFO] [0/DUC_1] Initializing block control (NOC ID: 0xD0C0000000000002) [INFO] [0/FIFO_0] Initializing block control (NOC ID: 0xF1F0000000000000) [INFO] [0/FIFO_1] Initializing block control (NOC ID: 0xF1F0000000000000) [INFO] [0/FIFO_2] Initializing block control (NOC ID: 0xF1F0000000000000) [INFO] [0/FIFO_3] Initializing block control (NOC ID: 0xF1F0000000000000) RF0: sample_rate=30.720 MHz dl_freq=3489.420 MHz ul_freq=3489.420 MHz (band n78) dl_ant=2 ul_ant=1 (ue) WARNING: The GPS is not locked. If you need time synchronization, you should restart the program when the GPS is locked. Chan Gain(dB) Freq(MHz) TX1 35.0 3489.420000 RX1 45.0 3489.420000 RX2 45.0 3489.420000 (ue) ue # UE_ID CL RNTI RRC_STATE EMM_STATE #ERAB IP_ADDR 5G 0 1 0 0 offline power off 0 5G 1 2 0 0 offline power off 0 (ue) power_on 1 2 (ue) ue # UE_ID CL RNTI RRC_STATE EMM_STATE #ERAB IP_ADDR 5G 0 1 0 0 idle registered 1 192.168.2.2 5G 1 2 0 4602 running registered 1 192.168.2.6 (ue)
- Type 'ue' at the prompt to see the status of the UEs and type 'power_on' to start a UE. The above simulation shows 2 UEs, and the number of UEs is specified UE_COUNT in the configuration file.
- Go back to 'mme' prompt in srv1-lg1 and check the gnb, ue list.
(mme) gnb PLMN RAN_ID IP:Port #UEctx TACs 310014 0x12345 127.0.1.1:49526 0 0x64 (mme) ue SUPI IMEISV CN M-TMSI/5G-TMSI REG TAC #BEARER IP_ADDR 001010123456789 0123456700000101 5GC 0x526d3bcc Y 310014. 0x64 1 192.168.2.2 001010123456790 0123456700000201 5GC 0xf33020aa Y 310014. 0x64 1 192.168.2.6 (mme)
- The base station (srv1-lg1) can now talk to the UEs via the IP addresses assigned above.
Using the Web Interface
- Amarisoft Web Interface can be used to analyse software logs and get information in real time. It can also be used to execute UE scenarios.
- Point your web browser to http://10.37.1.1/lte/ (10.37.1.1 is the CTRL IP address of srv1-lg1, where the MME and gNodeB are running)
- Click 'server' in the left client panel, and add MME, gNodeB, UE to look at the logs. Use the appropriate IP addresses and ports as shown below
|
Attachments (8)
- amarisoft_web_interface.JPG (179.3 KB ) - added by 2 years ago.
- amarisoft_add_server.JPG (25.7 KB ) - added by 2 years ago.
- chromedesktop.JPG (70.7 KB ) - added by 2 years ago.
- vysorphone.JPG (125.1 KB ) - added by 2 years ago.
- kb2005Amarisoft.JPG (34.0 KB ) - added by 2 years ago.
- kb2005Speedtest.JPG (23.2 KB ) - added by 2 years ago.
- uelistMME.JPG (31.0 KB ) - added by 2 years ago.
-
AmarisoftTutorial.png
(394.5 KB
) - added by 3 months ago.
Amarisoft Tutorial Block Diagram
Download all attachments as: .zip
Note:
See TracWiki
for help on using the wiki.
