wiki:Workshops/SigComm2022/MininetOptical

Context Navigation

Version 2 (modified by rajag, 2 years ago) ( diff )
—

Site Navigation

Setting up COSMOS' Optical Network topology using the Mininet-Optical Software Emulator

This wiki page is intended for participants attending COSMOS workshop in SIGCOMM 2022. This contains a tutorial for setting up a virtual/simulated optical network using Mininet-Optical. Mininet-Optical was developed as part of the COSMOS and COSM-IC projects and adds optical network emulation and simulation capabilities to Mininet to support software emulation of optical and packet-optical networks, including modeling of optical transmission effects and impairments.

This is a Mininet-Optical version of the tutorial at Workshops/Sig Comm2022/Optical Tutorial and is intended to show how an experiment designed for COSMOS' optical network testbed (hardware) may be adapted for use in a software emulation environment running on Linux (for example in a VM on a laptop or other hardware server), and how Mininet-Optical may be used to design experiments that will later be run on the COSMOS hardware testbed.

The Mininet-Optical version of this tutorial implements the same network topology and the same experiment as the hardware testbed tutorial, but there are differences between the software and hardware environments.

Authors:

Agastya Raj, Trinity College Dublin: rajag[at]tcd.ie
Julie Raulin, Tyndall National Institute: julie.raulin[at]tyndall.ie
Bob Lantz: University of Arizona: rlantz[at]cs.stanford.edu

This tutorial is based on hardware tutorial by T. Chen. et al. Please refer to Workshops/Sig Comm2022/Optical Tutorial for comparison with the hardware environment.

Description

The COSMOS testbed enables creation and use of optical networks of various topologies. Similarly, Mininet-Optical enables creation of virtual optical networks using software emulation. An example of how an optical network could be configured and used is provided. A simple experiment on switching of optical paths is described.

Compute Nodes and ToR switch interfaces used

Each compute node has 1 Ethernet interface:

srv1-co1-eth0
srv1-lg1-eth0
srv2-lg1-eth0

There are three ToR Ethernet interfaces:

sw-da-co1-eth1
sw-da-lg1-eth2
sw-da-lg1-eth3

There are three WDM transceivers, with separate output and input ports:
```
sw-da-co1-wdm320/321
sw-da-lg1-wdm290/291
sw-da-lg1-wdm310/311
```

and two COMB Sources, with Line-out ports:
```
comb1-wdm4201
comb2-wdm4201
```

Network Context

Fig.1 Logical Topology of the hardware used

This experiment demonstrates optical switching between the short (1-hop) path, between srv1-co1 and srv1-lg1, and the long (2-hop) path, between srv1-co1 and srv2-lg1. It represents changing of the light path in C-RAN when a "Client" wants to dynamically change its base-band processing location between a nearby "Edge Cloud" and a further away "Central Cloud".

To simulate the topology in hardware, the network component names are kept the same.

Experiment includes 3 servers:

srv1-co1 (192.168.1.1/24)
srv1-lg1 (192.168.1.2/24)
srv2-lg1 (192.168.1.3/24)]

Experiment includes 4 ROADMs:

rdm1-co1 (localhost:1834)
rdm1-lg1 (localhost:1832)
rdm2-lg1 (localhost:1833)
rdm2-co1 (localhost:1844)

2 ToR Switches are connected to the 3 servers on the following interfaces:

sw-da-co1-eth1 <--> srv1-co1-eth0
sw-da-lg1-eth2 <--> srv1-lg1-eth0
sw-da-lg1-eth3 <--> srv2-lg1-eth0

3 Ethernet interfaces and 3 WDM transceivers will be connected within the ToR switch:

sw-da-co1-eth1 ; sw-da-co1-wdm320/321  (output/input)
sw-da-lg1-eth2 ; sw-da-lg1-wdm290/291  (output/input)
sw-da-lg1-eth3 ; sw-da-lg1-wdm310/311  (output/input)

We are assigning the following wavelength to the transceivers:

1543.60 nm, 194.35 THz with bandwidth ~[194.30;194.40] THz
This corresponds to channel 61 in Mininet-Optical's as well as COSMOS' default channel grid.

We are assigning the following bands of wavelength to the comb sources to simulate background traffic:

Band 1: [1560.50,1564.10] nm ~ [191.80,192.25] THz. This corresponds to channels 10-19 in Mininet-Optical's and COSMOS' default channel grid.
Band 2: [1548.40,1552.00] nm ~ [193.30,193.75] THz. This corresponds to channels 40-49 in Mininet-Optical's and COSMOS' default channel grid.
Band 3: [1532.60,1536.10] nm ~ [195.30,195.75] THz. This corresponds to channels 80-89 in Mininet-Optical's and COSMOS' default channel grid.

Installing Mininet-Optical disk image on COSMOS' node

Before starting this tutorial, you will need to install Mininet-Optical in the console. We have already created a disk image with a pre-installed version of Mininet-Optical with necessary codes. If you don't have access to the COSMOS' console already, you can follow the sign-up and installation instructions at Workshops/Sig Comm2022/Signup Instructions

To install the Mininet-Optical disk image, follow the below steps:

Remove any installed disk images on the node

user@console:~$ omf tell -a reset -t <node>

Here, <node> is the name of the appropriate node (for example, node1-2.sb2.orbit-lab.org)

Install the Mininet-Optical OS image file.

user@console:~$ omf load -i sigcomm22-mnoptical-tutorial.ndz -t <node>

Turn the node on

user@console:~$ omf tell -a on -t <node>

Ping the node to check if disk image has been installed correctly
```
user@console:~$ ping <node>
```

$ ssh root@<node>
root@node# cd mininet-optical
root@node:~/mininet-optical# git fetch
root@node:~/mininet-optical# git checkout cosmos-tutorial
root@node:~/mininet-optical# git pull --rebase
root@node:~/mininet-optical# make install certs

Run a sample script to check Mininet-Optical has been installed correctly.

root@node:~/mininet-optical# sudo PYTHONPATH=. python3 ./examples/simpletest.py

Expected output:
root@node:~/mininet-optical# 
If your output looks like above, mininet-optical is successfully installed and working on your computer. Please exit the current Mininet-Optical script, by typing exit or pressing control-D at the mininet-optical> prompt:

If you are facing an error, please make sure you have followed the steps above, or consult one of our organizers for resolution.

The tutorial topology and a sample configuration script should be found in ~/mininet-optical/examples/sigcommtutorial.py and ~/mininet-optical/examples/config-sigcommtutorial.sh. If you want to test out Mininet-Optical on your computer after the tutorial, we have provided necessary resources in the appendix.

Setting Up the Optical Topology

In the COSMOS optical testbed, all devices are connected to a Calient S320 space switch. This switch serves as a programmable patch panel that allows any port to be connected to any other port, enabling realization of arbitrary topologies with fast re-connection between experiments.

It is possible to create a virtual space switch/programmable patch panel in Mininet-Optical to emulate the COSMOS optical testbed itself, but for this tutorial we will implement the topology using Mininet-Optical's topology API.

The Mininet-Optical emulated network is created using a Python script, examples/sigcommtutorial.py. Take a look at it now to see how the topology is implemented.

The topology itself is created using Mininet's high-level topology template API. Specifically, we create a subclass of class Topo and override the build() method:

class TutorialTopo( Topo ):
...
    def build( self ):

ROADMs, Comb Sources and ToR switches are added using addSwitch() calls:

    # ROADMs
    NC = NetconfPortBase
    rdm1co1 = self.addSwitch('rdm1co1', cls=LROADM, netconfPort=NC+4)
    ...
    # ToR switches
    swda_co1 = self.addSwitch('swda-co1', cls=Terminal, transceivers=[('32', -1.5*dBm)])
    ...
    #Comb Sources
    comb1 = self.addSwitch('comb1', cls=CombSource, power=comb1_power)
    ...

Servers are added using addHost() calls:

    # Servers
    srv1_co1 = self.addHost('srv1-co1')
        ...

In Mininet, ports are created by specifying port numbers when we add links. (This is due to the underlying link emulation which uses Linux virtual Ethernet (veth) pairs.)

Because of this, we need to specify the correct port numbers when we create the links.

The base port numbers for a Lumentum ROADM20 are specified at the top of the file:

# Lumentum Roadm20 Port numbering
LINEIN, LINEOUT = 5101, 4201
ADD, DROP = 4100, 5200

The server and ToR port numbers are as specified above. These port numbers are exactly the same as hardware experiment.

Boost and Pre-amp amplifiers associated with ROADMS are added accordingly in the inter-ROADM connections. WDM fiber links are unidirectional and are added using wdmLink() calls:

    # Inter-ROADM links
    # We put 32km of fiber between rdm2lg1 and rdm2co1
    # Default fiber length is 1m if not specified

    # Sub-millisecond delays won't be accurate (due to scheduler timing
    # granularity and running in a VM) but this will add observable
    # propagation delay for the longer links.

    self.wdmLink(rdm1co1, rdm1lg1, LINEOUT, LINEIN, 
        spans=[0.0*m,
            ('boost', {'target_gain': 18.0*dB, 'wdg_id': 'wdg1'}), 
            10.0*km, 
            ('preamp', {'target_gain': 18.0*dB, 'wdg_id': 'wdg1'})], 
        delay='33us')

     self.wdmLink(rdm1lg1, rdm1co1, LINEOUT, LINEIN, 
        spans=[0.0*m,
            ('boost', {'target_gain': 18.0*dB, 'wdg_id': 'linear'}),
            10.0*km, 
            ('preamp', {'target_gain': 18.0*dB, 'wdg_id': 'linear'})], 
        delay='33us')

    # Configuring Optical links between rdm1-lg1 and rdm2-lg1
    self.wdmLink(rdm1lg1, rdm2lg1, DROP+11, ADD+11)      # Forward pass-through
    self.wdmLink(rdm2lg1, rdm1lg1, DROP+11, ADD+11)      # Backward pass-through

    # Configuring Optical Links between rdm2-lg1 and rdm2-co1
    self.wdmLink(rdm2lg1, rdm2co1, LINEOUT, LINEIN, 
        spans=[0.0*m,
           ('boost', {'target_gain': 18.0*dB, 'wdg_id': 'wdg1'}),
            32.0*km, 
            ('preamp', {'target_gain': 18.0*dB, 'wdg_id': 'wdg1'})], 
        delay='106us')                                   # Forward Link
    self.wdmLink(rdm2co1, rdm2lg1, LINEOUT, LINEIN, 
       spans=[0.0*m,
            ('boost', {'target_gain': 18.0*dB, 'wdg_id': 'wdg2'}),
            32.0*km, 
            ('preamp', {'target_gain': 18.0*dB, 'wdg_id': 'wdg2'})], 
        delay='106us')                                   # Backward Link

    # ROADM add/drop 2 <-> ToR transceiver links
    self.wdmLink(swda_co1, rdm1co1, 320, ADD+2)        #Forward Link
    self.wdmLink(rdm1co1, swda_co1, DROP+2, 321)       #Backward Link
    ...
    # Configuring Optical Links between Comb Source and Tor ROADMS
    self.wdmLink(comb1, rdm1co1, CombSource.LINEOUT, ADD+1)
    ...
    # Configuring Ethernet connections between Servers and Tor switches
    self.addLink(server1, swda_co1, port1=0, port2=1)

Lastly, the topology and network objects are instantiated and everything is started up (and shut down) in the __main__ section of the network setup script:

if __name__ == '__main__':
    ...
    topo = TutorialTopo()
    net = Mininet( topo=topo, controller=None )
    restServer = RestServer( net )
    net.start()
    restServer.start()
    netconfServer = NetconfServer(
        net, username=username, password=password, sslkeyfile=sslkeyfile )
    netconfServer.start()
    ...
    if 'test' in argv:
        test(net)
    else:
        info(TutorialTopo.__doc__+'\n')
        CLI(net)
    netconfServer.stop()
    restServer.stop()
    net.stop()
    info( 'Done.\n')

Creating the Mininet-Optical Network

All of these commands should be run in a terminal window for the VM or server where Mininet-Optical is installed.

We will run Mininet-Optical from the top directory of the source tree:

root@node:# cd ~/mininet-optical

We should check to make sure that the tutorial scripts are present:

root@node:~/mininet-optical# ls examples/sigcommtutorial.py
root@node:~/mininet-optical# ls examples/config-sigcommtutorial.sh

If they are missing, we can fetch and install the appropriate branch:

root@node:~/mininet-optical# git fetch
root@node:~/mininet-optical# git checkout cosmos-tutorial
root@node:~/mininet-optical# make install

Since the NETCONF agents for the ROADMs use SSL, we first have to generate a set of (self-signed) SSL certificates for them to use:

root@node:~/mininet-optical# make certs

Now we should be able to run the tutorial script to create the emulated network:

root@node:~/mininet-optical# sudo PYTHONPATH=. examples/sigcommtutorial.py

This should start up Mininet-Optical, create the tutorial network, and start the CLI:

SIGCOMM22 mini-tutorial topology


comb1 -> rdm1co1 <--10km--> rdm1lg1 || rdm2lg1 <--34km--> rdm2co1 <- comb2
           |                  |                              |
        swda_co1           swda_lg1--------------------------|
           |                  |                              |
        srv1-co1           srv1-lg1                       srv2-lg1

This is for the SIGCOMM22 mini-tutorial at:
https://wiki.cosmos-lab.org/wiki/Workshops/SigComm2022/MininetOptical

*** Starting CLI:
mininet-optical>

Mininet-Optical CLI commands may be entered at the mininet-optical> prompt.

Controller Configuration

Now that we have the topology setup for the network, we want to configure the lightpaths and pass packets using NETCONF, which is network management protocol for software defined networks. We have this configuration in the file examples/config-sigcommtutorial.py, which we require to run from another terminal window.

(Note: if you want to use the X11 features of Mininet, such as the xterm or plot commands, you may need to use sudo HOME=~ rather than just sudo.) <Should we add instructions to setup x11?>

If you don't have one open already, open up another terminal window with the below instructions:

[WIP] Opening another terminal window in Orbit

SSH into

user@console:~$ cd ~/mininet-optical

Connect to the VM where Mininet-Optical is installed

user@console:~$ cd ~/mininet-optical

Enter source directory

user@console:~$ cd ~/mininet-optical

Unless specified otherwise, all of the configuration commands below should be entered in this second window at the shell prompt. All of these configurations can be performed by Python scripts developed to work with the COSMOS test-bed. The Python commands send NETCONF commands to the ROADM.

Running the configuration script

Run the script with the following command

root@node:~/mininet-optical# bash -x ./examples/config-sigcommtutorial.py

This executes the configuration file which establishes the ground connections first and turns on the transceivers. We walk through this script below to deep dive into what's happening.

Mininet-Optical's Terminal is the equivalent of the ToR switch which contains Ethernet interfaces as well as WDM transceivers.

Instead of using a Cisco-style CLI to configure it, we use its default REST API.

As noted above, 194.35 THz corresponds to channel C61 on Mininet-Optical's default 50GHz channel grid. C1's middle frequency is 191350 GHz, so C61 is at 191350 + 60*50 = 194350 GHz.

Connect Ethernet interfaces to Transceivers and set channel

curl "$swda_co1/connect?node=swda-co1&ethPort=1&wdmPort=320&wdmInPort=321&channel=61"
curl "$swda_lg1/connect?node=swda-lg1&ethPort=2&wdmPort=290&wdmInPort=291&channel=61"
curl "$swda_lg1/connect?node=swda-lg1&ethPort=3&wdmPort=310&wdmInPort=311&channel=61"

Turn on all transceivers and comb sources

curl "$swda_co1/turn_on?node=swda-co1"
curl "$swda_lg1/turn_on?node=swda-lg1"
curl "$comb1/turn_on?node=comb1"
curl "$comb2/turn_on?node=comb2"

Configure Ethernet interfaces and assign IP addresses:

...
m=~/mininet/util/m
...
$m srv1-co1 ifconfig srv1-co1-eth0 192.168.1.1/24
$m srv1-lg1 ifconfig srv1-lg1-eth0 192.168.1.2/24
$m srv2-lg1 ifconfig srv2-lg1-eth0 192.168.1.3/24

Note that ~/mininet/util/m can be used to 'log in' to any one of the servers much as you would with ssh (but it actually spawns a shell in the appropriate cgroup/network namespace.)

Performing base test configuration

Once you execute the script, the script will ask for a prompt to perform a base test. This test pings 'srv-co1' to 'srv-lg1'; and pings 'srv-co1' to 'srv2-lg1' without establishing any lightpath connections between ROADMS. Press Return key to perform the base test.

*** Base test before configuration
press return to test base configuration>
...
*** srv1-co1 pinging srv1-lg1
PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
64 bytes from 192.168.1.2: icmp_seq=1 ttl=64 time=0.932 ms
64 bytes from 192.168.1.2: icmp_seq=2 ttl=64 time=0.145 ms
64 bytes from 192.168.1.2: icmp_seq=3 ttl=64 time=0.153 ms

--- 192.168.1.2 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2089ms
rtt min/avg/max/mdev = 0.145/0.410/0.932/0.369 ms
...
*** srv1-co1 pinging srv2-lg1
PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data.
From 192.168.1.1 icmp_seq=1 Destination Host Unreachable
From 192.168.1.1 icmp_seq=2 Destination Host Unreachable
From 192.168.1.1 icmp_seq=3 Destination Host Unreachable

--- 192.168.1.3 ping statistics ---
3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2192ms

As expected, none of the servers are able to ping each other because lightpath connections have not been established as of yet.

Configuring ROADMs

ROADMs in Mininet-Optical may be configured via several mechanisms. An internal Python API may be used for configuration within the script that creates the network. More realistically, two external SDN/RPC control interfaces are provided: a simple REST interface and a more realistic NETCONF interface which is partially compatible with the NETCONF interface of the hardware Lumentum ROADM20.

For this tutorial, we are using NETCONF interface to configure the ROADMs to closely match the interface used in hardware experiment.

[WIP] MUX/DEMUX configuration

As a reminder, here are the ROADM port numbers:

rdm1-co1:

MUX IN/OUT (ADD1/LINEOUT) port: 4101/4201
DEMUX IN/OUT (LINEIN/DROP1)port: 5101/5201

rdm1-lg1:

MUX IN/OUT (ADD1/LINEOUT) port: 4101/4201
DEMUX IN/OUT (LINEIN/DROP1) port: 5101/5201

rdm2-lg1:

MUX IN/OUT (ADD1/LINEOUT) port: 4101/4201
DEMUX IN/OUT (LINEIN/DROP1) port: 5101/5201

rdm2-co1:

MUX IN/OUT (ADD1/LINEOUT) port: 4101/5201
DEMUX IN/OUT (LINEIN/DROP1) port: 5101/5201

Note that the servers are connected to ADD2/DROP2 [4102/5202] while ADD11/DROP11 [4111/5211] are used as passthrough ports between rdm1-lg1 and rdm2-lg1.

Also note that these port numbers are the same as the hardware tutorial page.

Network Interfaces Configuration for Experiment-1 (short-hop)

In Experiment 1, we are choosing to pass the optical signal through 1 hop (via a pair of 10km fiber spools). This requires us to establish a connection between rdm1-co1 and rdm1-lg1. Once you perform the base test as described above, the script will prompt you to press Return key to perform the test for configuration 1. Before trying the configuration, let's dive into what connections this script will install:

Configuring srv1-co1⇐⇒srv1-lg1 Connection 1 on Mininet-Optical using NETCONF

The NETCONF servers for rdm1-co1 and rdm1-lg1 are listening on localhost at ports 1834 and 1831, respectively. We will use the examples/nc_add_connection.py script to configure connections using NETCONF.

testdir=$(dirname $0)
addc=$testdir/nc_add_connection.py
rdm1_co1=localhost:1834
rdm1_lg1=localhost:1831

rdm1-co1:

Enable MUX port 4102 “From sw-da-co1”
Add Connection “Exp1_From_sw-da-co1” with Input/ Output Port 4102/4201 with bandwidth [194.30;194.40] THz
Enable DEMUX port 5202 “Toward sw-da-co1”
Add Connection “Exp1_Toward_sw-da-co1” with I/O Port 5101/5202

Note that MUX/ADD/LINEOUT is module 1 and DEMUX/DROP/LINEIN is module 2. We are calling all of our connections connection 10. The interfaces are in-service and blocked is false. The 5 is an attenuation setting which may currently be ignored in Mininet-Optical.

$addc $rdm1_co1 1 10 in-service false 4102 4201 194300 194400 5 Exp1_From_sw-da-co1
$addc $rdm1_co1 2 10 in-service false 5101 5202 194300 194400 5 Exp1-Toward_sw-da_co1

rdm1-lg1:

Enable MUX port 4102 “From sw-da-lg1”
Add Connection “Exp1_From_sw-da-lg1” with I/O Port 4102/4201 with bandwidth [194.30;194.40] THz
Enable DEMUX port 5202 “Towards sw-da-lg1”
Add Connection “Exp1_Towards_sw-da-lg1” with I/O Port 5101/5202

$addc $rdm1_lg1 1 10 in-service false 4102 4201 194300 194400 5 Exp1_From_sw-da-lg1
$addc $rdm1_lg1 2 10 in-service false 5101 5202 194300 194400 5 Exp1_Toward_sw-da-lg1

Performing the experiment and results

Now you can try installing the above lightpaths by yourself. As prompted by the terminal, press Return to install the configuration and perform the test. This will establish the connections between ROADMs as described above, which you can also view with the lines printed.

...
*** Test configuration 1
press return to configure and test configuration 1>
...
*** Installing ROADM configuration 1 for srv1-co1<-->srv1-lg1 (NETCONF)
...
*** srv1-co1 pinging srv1-lg1
PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
64 bytes from 192.168.1.2: icmp_seq=1 ttl=64 time=0.724 ms
64 bytes from 192.168.1.2: icmp_seq=2 ttl=64 time=0.164 ms
64 bytes from 192.168.1.2: icmp_seq=3 ttl=64 time=0.130 ms

--- 192.168.1.2 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2130ms
rtt min/avg/max/mdev = 0.130/0.339/0.724/0.272 ms

...

*** srv1-co1 pinging srv2-lg1
PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data.
From 192.168.1.1 icmp_seq=1 Destination Host Unreachable
From 192.168.1.1 icmp_seq=2 Destination Host Unreachable
From 192.168.1.1 icmp_seq=3 Destination Host Unreachable

--- 192.168.1.3 ping statistics ---
3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2192ms

As expected, srv1-co1 and srv1-lg1 are able to ping each other because we established the ROADM rules for short-hop configuration. Consequently, srv1-co1 and srv2-lg1 are not able to ping each other because no such connection is established yet.

Note that the average ping time for srv1-co1 to srv1-lg1 is 0.339 ms.

Note that the Mininet-Optical ROADM dataplane is currently modeled using OvS switching in the Linux kernel, so each hop will add some delay that would not be seen on hardware. Process scheduling, OS and VM overhead, etc. can create additional delays in a software emulator.

Network Interfaces Configuration for Experiment-2 (long-hop)

In Experiment 2, we are choosing to pass the optical signal through 2 hops (via a pair of 10km fiber spools with the 32km Manhattan dark fiber). This requires us to establish a connection between srv1-co1 and srv2-lg1. Once you perform the experiment 1 as described above, the script will prompt you to press Return key to perform the test for configuration 2. Before trying the configuration, let's dive into what connections this script will install:

Configuring srv1-co1⇐⇒srv2-lg1 connection on Mininet-Optical using NETCONF

The NETCONF servers for rdm1-co1 and rdm1-lg1 are listening on localhost at ports 1834 and 1831 as Experiment 1. We are configuring rdm2-lg1' and 'rdm2-co1 to listen at ports 1832 and 1833 respectively. Like Experiment 1 we are using examples/nc_add_connection.py script to configure connections using NETCONF.

testdir=$(dirname $0)
addc=$testdir/nc_add_connection.py
rdm1_co1=localhost:1834
rdm1_lg1=localhost:1831
rdm2_lg1=localhost:1832
rdm2_co1=localhost:1833

rdm1-co1 (Same configuration as for Experiment 1):

Enable MUX port 4102 “From sw-da-co1”
Add Connection “Exp2_From_sw-da-co1” with I/O Port 4102/4201 with bandwidth [194.30;194.40] THz
Enable DEMUX port 5202 “Toward sw-da-co1”
Add Connection “Exp2_Toward_sw-da-co1” with I/O Port 5101/5202 with bandwidth [194.30;194.40] THz

$addc $rdm1_co1 1 10 in-service false 4102 4201 194300 194400 5 Exp2-From_sw-da-co1
$addc $rdm1_co1 2 10 in-service false 5101 5202 194300 194400 5 Exp2_Toward_sw-da-co1

rdm1-lg1 (Different configuration from Experiment 1):

Enable MUX port 4111 “Through Port”
Add East-bound Connection “Exp2_East_rdm1-lg1” with I/O Port 4111/4201 with bandwidth [194.30;194.40] THz
Enable DEMUX port 5211 “Through Port”
Add West-bound Connection “Exp2_West_rdm1-lg1” with I/O Port 5101/5211 with bandwidth [194.30;194.40] THz

This time we pass channel 61 through rdm1-lg1:

$addc $rdm1_lg1 1 10 in-service false 4111 4201 194300 194400 5 Exp2_East_rdm1-lg1
$addc $rdm1_lg1 2 10 in-service false 5101 5211 194300 194400 5 Exp2_West_rdm1-lg1

rdm2-lg1:

Enable MUX port 4111 “Through Port”
Add East-bound Connection “Exp2_East_rdm2-lg1” with I/O Port 4111/4201 with bandwidth [194.30;194.40] THz
Enable DEMUX port 5211 “Through Port”
Add West-bound Connection “Exp2_West_rdm2-lg1” with I/O Port 5101/5211 with bandwidth [194.30;194.40] THz

And pass through rdm2-lg1:

$addc $rdm2_lg1 1 10 in-service false 4111 4201 194300 194400 5 Exp2_East_rdm2-lg1
$addc $rdm2_lg1 2 10 in-service false 5101 5211 194300 194400 5 Exp2_West_rdm2-lg1

rdm2-co1 (Same As For rdm1-co1):

Enable MUX port 4102 “From sw-da-lg1”
Add Connection “Exp2_From_sw-da-lg1” with I/O Port 4102/4201 with bandwidth [194.30;194.40]
Enable DEMUX port 5202 “Towards sw-da-lg1”
Add Connection “Exp2_Towards_sw-da-lg1” with I/O Port 5101/5202 with bandwidth [194.30;194.40]

And we drop at rdm2-co1:

$addc $rdm2_co1 1 10 in-service false 4102 4201 194300 194400 5 Exp1-Fromswda_lg1
$addc $rdm2_co1 2 10 in-service false 5101 5202 194300 194400 5 Exp1-Torwardswda_lg1

Performing Experiment 2 and Results

Now you can try installing the above lightpaths for Experiment 2 by yourself. As prompted by the terminal, press Return to install the configuration and perform the test. This will establish the connections between ROADMs as described above, which you can also view with the lines printed.

...
*** Test Experiment 2
press return to configure and perform Experiment 2> 
...
*** Installing ROADM configuration for srv1-co1<-->srv2-lg1 (NETCONF)
...
*** srv1-co1 pinging srv1-lg1
PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
From 192.168.1.1 icmp_seq=1 Destination Host Unreachable
From 192.168.1.1 icmp_seq=2 Destination Host Unreachable
From 192.168.1.1 icmp_seq=3 Destination Host Unreachable

--- 192.168.1.2 ping statistics ---
3 packets transmitted, 0 received, 100% packet loss, time 2070ms

...

*** srv1-co1 pinging srv2-lg1
PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data.
64 bytes from 192.168.1.3: icmp_seq=1 ttl=64 time=1.21 ms
64 bytes from 192.168.1.3: icmp_seq=2 ttl=64 time=0.385 ms
64 bytes from 192.168.1.3: icmp_seq=3 ttl=64 time=0.430 ms

--- 192.168.1.3 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2072ms
rtt min/avg/max/mdev = 0.385/0.675/1.211/0.379 ms

As expected, srv1-co1 and srv2-lg1 are able to ping each other because we established the ROADM rules for long-hop configuration. Consequently, as opposed to Experiment 1, srv1-co1 and srv1-lg1 are not able to ping each other because no such connection is established yet.

Note that the average ping time for srv1-co1 to srv2-lg1 is 0.675 ms, and the average ping time for srv1-co1 to srv1-lg1 in Experiment 1 was 0.339 ms. Observe the slightly longer RTT to srv2-lg1, reflecting the increased propagation time across two 32km fibers to reach the "Central Cloud" data center.

Shutting down Mininet-Optical

To exit Mininet-Optical, type exit or press control-D at the mininet-optical> prompt.

References

COSMOS Optical Hardware Testbed Tutorial: Workshops/Sig Comm2022/Optical Tutorial

Mininet-Optical Tutorial network script: https://github.com/Mininet-Optical/mininet-optical/blob/cosmos-tutorial/mnoptical/examples/sigcommtutorial.py

Mininet-Optical Tutorial configuration script: https://github.com/Mininet-Optical/mininet-optical/blob/cosmos-tutorial/mnoptical/examples/config-sigcommtutorial.sh

Mininet-Optical documentation: https://mininet-optical.org

Mininet-Optical code: https://github.com/mininet-optical/mininet-optical

(Packet) Mininet web site: https://mininet.org

Attachments (1)

sigcomm2022tutorial_topology.png (68.1 KB ) - added by rajag 2 years ago.

Download all attachments as: .zip

Note: See TracWiki for help on using the wiki.

Download in other formats:

Plain Text